- 1.) Do not stack directly on the concrete floor or in the ground; This should not be done in wet and humid places.
- 2.) Heated glasses should be stored on pallets placed near vertical (at an angle of ~ 10 °) on the long side and vertically on the base of the pallet.
- 3.) Contact with glass should be avoided by placing a separator (eg a cork wedge) between each unit.
- 4.) The rear of the units should rest on the pallet, avoiding point load impacts and the unique mosque of the Isıcam unit touching the ground. Otherwise, swelling may occur due to pressure changes, and as a result of 2-3 times the force load, fractures or deformities may occur.
- 5.) When stacking insulating glazing of different sizes, small glasses should be placed in front of large glasses, longitudinal slats must be placed between two glasses to avoid any pressure from the center and the space between the slats should not must not exceed 50 cm.
- 6.) In cases where the insulating pastes located on the edges of the insulating glazing can be exposed to direct sunlight, it is necessary to use silicone as a secondary seal in the insulating glazing.
- 7.) Glasses and joinery shipped must be kept away from sun and rain, our company is not responsible for errors resulting from storage conditions.
- 8.) Our company is not responsible for breakage caused by the risk of thermal breakage of the glasses shipped before and after assembly.
- 9.) Whether the pressure hole is open or not, all fittings intended for local and overseas market must be specified by customer when ordering glass, our company is not responsible for any damage that may occur if not specified.
- 10.) Moreover, it is not directly related to this problem, but it should be noted that colored and reflective coatings should be used as tempered in systems such as glass, and regardless of the type of glass, if the edges glasses are damaged during assembly. (or if high pressure is created on the edges of the glass), it should be noted that the glasses can break due to thermal expansions during use.
- 11.) The materials to be used in the assembly of Isıcam brand products (structural silicones, sealing silicones, silicone sealants, adhesives, etc.) must be suitable materials which do not contain acidic solvents.
- 12.) In the event of contact between the Isıcam units and the assembly materials (structural silicones, sealing silicones, sealants, adhesives, etc.), compatibility tests of these materials with the primary and secondary insulating pastes (polysulphide, polyurethane, insulating glass sealant) used in Isıcam production must be carried out. It is the responsibility of the assembly company carrying out the application to have these conformity tests carried out in the laboratories of the silicone manufacturers.
- 13.) In addition, it should also be clarified that the responsibility arising from failures that will occur in the event of failure to comply with these warnings will lie with their (assembly company).
- 1.) Glasses packed in crates in overseas projects are delivered from the EXW factory "TURAN CAM ÇEKEKÖY".
- 2.) All claims will be assessed against the standards described above. In order for the glasses to be cut as exported, the necessary documents must reach us completely.
- 3.) In this case, VAT is not requested. If the customer notifies the approved purchase order by e-mail or fax, our company will be deemed to have the right to receive and charge the price of the product ordered - even if the customer ceases to receive finance.
- 4.) Delivery date: Following the final confirmation of the order, it will be delivered separately according to stocks and the production schedule. For payments not made by the due date, a monthly interest of 3% on TL is applied. In bank payments, the cost of the transfer belongs to the customer.
- 1.) TS EN 572-2 Float Cam
- 2.) TS EN 1096 Coated Glasses Used in Buildings
- 3.) TS 3539 EN 1279 Double Glass Units
- 4.) TS EN 12150 Fully Tempered Glasses
- 5.) TS EN 1863 Partially Tempered Glasses
- 6.) TS-EN-Iso-12543 1-6 Laminated Glass and Laminated Safety Glass Used in Buildings